Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Beverly Hills, CA | Ironworks Gate Co.
We’re an independent Ghost Controls service provider, not a manufacturer affiliate, and we repair these operators across Beverly Hills from the flats south of Santa Monica Boulevard to the canyons above Sunset. The short version: most Ghost Controls failures here come down to two things, heavy custom gate panels that outgrew the motor and coastal air eating at the hardware. Call (442) 255-3886 and Victor Salinas or one of our techs will give you a straight answer about what’s wrong and what it costs to fix.
We service the full Ghost Controls lineup, AXDP swing arms, AXZL and HDP1 slide operators, TSS1 solar systems, and their battery backups, and we keep genuine boards and arms stocked for same-week turnaround in Beverly Hills. For the full scope of what we do on this brand, see our Ghost Controls sales & service page. If your gate is giving you trouble, let’s take a look at it, no guessing, no upselling, just a straight answer.
Why Beverly Hills Residents Choose Us for Ghost Controls Service
Ghost Controls operators show up on a lot of Beverly Hills driveways because they’re affordable and easy to install, which also means they show up on a lot of gates that are too heavy for them. We’ve been called out to estates where a 12-foot wrought-iron panel is swinging on a residential-rated motor, and the owner’s been through two boards in three years. That’s not a board problem. That’s a capacity problem, and we’ll tell you so plainly.
Victor Salinas grew up in the Eastside flats of West Hollywood watching his uncle weld ornamental iron on Melrose Avenue, then studied welding and electrical systems at Los Angeles Trade-Technical College downtown. Four decades later, he’s seen just about every way a gate operator can fail on this side of the hills. Our techs know which Ghost Controls parts fail under Beverly Hills conditions and which repairs will actually hold up here.
Common Ghost Controls Gate Repair Problems We Solve in Beverly Hills
- Burned control board relays on AXDP and AXZL units. We see this constantly in the flats, where estate owners added heavier gate panels over the years without upgrading the motor. The original residential-rated relay isn’t built for a gate that now weighs 200 pounds over spec, and it fails, usually right after a busy holiday week of cycling.
- Snapped plastic release levers on AXDP and AXZL arms. Santa Ana wind events push hard against full-height ornamental panels, especially on canyon-facing gates above Sunset. The lateral load snaps that plastic lever clean off, and the gate won’t budge until it’s replaced.
- Limit switch drift on HDP1 slide operators. On steep, curved driveways in the canyons north of Sunset, the gate stops two or three inches short of fully closed. Homeowners hear the gap before they see it, and it sets off every alarm on the property.
- Battery backup failure on older AXZB units. North-facing and canyon-shaded gates stay damp from the marine layer, and after one season the battery won’t hold a charge. The keypad throws a false “AC power loss” alert and the gate defaults to manual or stalls mid-cycle.
- Seized hinge bearings on original ironwork. Decades of coastal salt air work into bronze bearings on gates mounted to 1920s and 1930s brick or stone pilasters. The motor fights 40 extra pounds of friction and eventually quits, but the real problem predates the opener.
Ghost Controls Service in Beverly Hills: What Local Conditions Mean for Your Equipment
Here’s something you won’t find on a generic Ghost Controls page: Beverly Hills runs its own Building & Safety division, and it requires a permit and inspection for any modification to an automatic gate operator. That includes replacing a Ghost Controls opener with a different model. We’ve taken over jobs where an out-of-town contractor swapped a motor, collected payment, and disappeared, leaving the homeowner with a failed final inspection and no route to close it out. Our crew files and closes that permit every time, because a surprising number of our repair calls start as a “completed” upgrade that was never approved.
That’s the single biggest difference between Ghost Controls repair work in Beverly Hills and the same job three miles away in West Hollywood or unincorporated LA County. The equipment fails the same way. The paperwork does not.
Ghost Controls Models & Products We Service in Beverly Hills
We service the AXDP series dual swing gate openers, the AXZL and HDP1 slide gate opener lines, the TSS1 solar swing gate opener, and the AXZB battery backup units. When a Ghost Controls unit is under five years old and the gate is within the motor’s rated weight, we install genuine Ghost Controls replacement boards and arms. Aftermarket boards often don’t map the limit and remote learn functions correctly, and you end up paying twice.
For older systems, or when the gate panel has been upgraded beyond what the original motor was ever rated to carry, we quote a full actuator and control retrofit to a heavier-rated opener instead of replacing the same burned board every eighteen months. That’s the honest math.
Ghost Controls Service Pricing in Beverly Hills
Ghost Controls repair work in Beverly Hills typically falls in these ranges, depending on what we find when we open the cover:
- Diagnostic service call: $89 to $149, applied toward the repair if you proceed
- Control board replacement (genuine Ghost Controls): $220 to $380 installed
- Arm or actuator replacement: $180 to $340 per arm
- Battery backup replacement: $120 to $210
- Full actuator and control retrofit to a heavier-rated opener: $1,400 to $2,900 depending on gate weight, length, and power run
The price is quoted and agreed before any work starts, in writing. No surprises on the bill. Call (442) 255-3886 for a free estimate.
Serving Beverly Hills, CA - Our Local Coverage Area
We’re based in the Beverly Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Beverly Hills
Yes. Replacing a failed component with the same model, like a factory Ghost Controls control board in an existing approved operator, does not require a new permit. If you’re changing the operator model or moving the gate’s configuration, that’s where Beverly Hills Building & Safety requires a permit and inspection. We’ll tell you which applies before you spend a dollar. Call (442) 255-3886 and we’ll walk you through it.
The click is usually the relay trying to engage while the plastic release lever, or the arm itself, has broken under the lateral wind load. Full-height ornamental panels on canyon-facing gates take the worst of it. The fix is replacing the arm or lever, and in some cases reinforcing the bracket so it doesn’t happen again next wind season.
In Beverly Hills, the usual culprit is a failed AXZB battery backup on a north-facing or canyon-shaded gate. The damp marine layer air corrodes the battery contacts or the battery simply won’t hold charge anymore, and the system misreads it as a power loss. We replace the battery and test the charging circuit in one visit.
Yes, and you should. A heavier custom panel on a residential-rated Ghost Controls motor will burn boards and strain arms within a year or two. We’ll spec our Gate Installation in Beverly Hills with a heavier-rated opener sized to the new panel’s weight and wind load, then file and close the Beverly Hills permit. Call (442) 255-3886 for exact numbers before you commission the fabrication.
That’s limit switch drift on an HDP1 slide opener, and it shows up most often on steep Beverly Hills driveways where the motor works harder against grade. The switch reads the gate position slightly off after repeated load, and the gate stops short. We reset and recalibrate the limits, and if it recurs, we replace the switch rather than band-aid it.
Service Areas Near Beverly Hills
We serve all of Beverly Hills service area, from the flats to the canyons, plus Ghost Controls service in Los Feliz, Ghost Controls service in West Hollywood, Hancock Park, Silver Lake, and Echo Park. Same crew, same standards, same warranty.
Book Your Ghost Controls Service in Beverly Hills Today
A live person answers the phone 24 hours a day, seven days a week. Call (442) 255-3886 and we’ll schedule a diagnostic, usually within 24 hours. The estimate is free, the price is agreed upfront, and the work is backed by our written 90-Day Done Right Promise.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving Beverly Hills since 1984.