Ghost Controls Gate Repair Nationwide

Ghost Controls Gate Repair in West Hollywood: What to Know First

Ghost Controls gate repair in West Hollywood typically runs $185-$475 depending on whether the issue is a failed control board, a stripped gear assembly, or a sensor out of alignment. Most Ghost Controls jobs are completed in a single visit, and we quote the full price before work begins so there are no surprises on the bill. We’re an independent Ghost Controls service provider, not a factory affiliate, which means we fix what’s actually broken instead of pushing a full system replacement.

Call (442) 255-3886

This page is for West Hollywood homeowners whose Ghost Controls opener has started acting up: a gate that stops halfway, a keypad that stopped talking to the board, a motor that hums but won’t move the gate. If that’s you, call (442) 255-3886 and a live person will answer, any hour, any day.

Key takeaways:

• Ghost Controls repair in West Hollywood is usually done same-day or next-day, not weeks out.
• We service the full Ghost Controls line: TSS1, TDS2, HYPRO, and the R2 series, plus solar and AC-powered kits.
• Every repair carries our written 90-Day Done Right Promise.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls is a fine opener brand for the price, but after 42 years of working on gates across West Hollywood, we’ve learned where these units tend to give up. Here’s what we see most often, and what we do about it:

• TSS1 and HYPRO control boards damaged by power surges. West Hollywood’s older hillside neighborhoods have tree branches that swing into overhead lines during Santa Ana wind events, and the resulting voltage spikes are hard on gate electronics. We replace the board with an OEM unit when the opener is still under warranty, or a quality aftermarket board with matching specs when it isn’t. We also add a surge protector to the power feed so it doesn’t happen again in six months.
• Stripped gear assemblies on the TDS2 dual-swing series. Ghost Controls uses a plastic gear train inside the actuator arm, and over time, a gate that’s even slightly out of balance will chew those teeth down. This is a series-specific symptom: the motor powers on, you hear a grinding sound, and the gate doesn’t move. The fix is replacing the gear assembly and rebalancing the gate leaf so the new gears aren’t doing all the pulling.
• Photo-eye misalignment from driveway shifting. West Hollywood sits on a mix of clay and decomposed granite, and driveways move. A photo-eye that was perfectly aligned at installation can be off by a quarter inch a year later, and the gate will refuse to close because it thinks something’s in the way. This is a 20-minute fix, and we show you how to spot it before you call us next time.
• Solar panel wiring that can’t keep up with shorter winter days. A lot of West Hollywood homes run their Ghost Controls opener on the solar kit, and it works well until December. The panel gets shaded by a neighbor’s roofline, the battery drains, and the gate starts moving at half speed before it quits entirely. We relocate the panel, upgrade the charge controller, or convert the system to AC power if there’s a convenient circuit nearby.
• Remote control range that fades after a few years. This one isn’t the opener’s fault: the receiver antenna gets pinched inside the control box, or the remote’s battery contacts corrode in West Hollywood’s marine-layer humidity. We test the receiver output, replace the antenna if needed, and re-sync the remotes. If you’re still running the original remotes from 2018, we’ll tell you honestly when it’s time for new ones.

One thing we see often enough to mention: Ghost Controls openers are forgiving, but they’re not quiet. If your gate suddenly sounds like a coffee grinder, don’t keep running it. Call us. A stripped gear is a $160 problem on day one and a $400 problem on day thirty.

Our Ghost Controls Gate Repair Process

When you call us about a Ghost Controls opener, here’s what happens from the moment we pick up the phone:

1. 1
   You describe the problem. A live person answers, asks a few questions about what the gate is doing or not doing, and schedules a visit. We’ll give you a straight arrival window and we’ll be there when we say.
2. 2
   We diagnose on site. Our technician checks the control board, limit switches, gear assembly, photo-eyes, power supply, and remote sync. We don’t guess and we don’t start swapping parts until we know what failed.
3. 3
   We give you a fixed price before touching a bolt. You’ll know exactly what the repair costs, what parts we’re using, and whether OEM or aftermarket makes more sense for your opener. You approve it, then we work. No invoice surprises.
4. 4
   We do the repair. For most Ghost Controls issues - board swaps, gear replacements, sensor realignment, remote re-sync - the work is done in one visit. If a part is rare and needs to be ordered, we tell you that upfront and give you a timeline.
5. 5
   We test it like we’ll be the next person to use it. Full open and close cycles, obstruction testing, auto-close timing, and remote range check. The gate gets run through everything a normal week would throw at it.
6. 6
   We leave you with the 90-Day Done Right Promise in writing. If the same issue comes back within 90 days, we come back and fix it. No arguing, no paperwork, no exceptions.

What Ghost Controls Gate Repair Costs in West Hollywood

Here’s what you can expect to pay for common Ghost Controls repairs in the West Hollywood area:

• Photo-eye realignment or obstruction sensor issue: $95-$150
• Remote re-sync or antenna replacement: $75-$125
• Battery replacement (solar kits): $90-$160
• Control board replacement: $220-$380
• Gear assembly replacement (TDS2/HYPRO): $180-$340
• Complete actuator arm replacement: $350-$475

What moves the price: whether the part is OEM or aftermarket, how hard the gate is to access, and whether we find a second issue while we’re in there. You’ll know the total before we start. We offer a free second opinion on any written estimate, $50 off any repair over $250, and a permanent 5% discount for seniors and veterans. Call (442) 255-3886 and we’ll give you an honest number.

Why West Hollywood Homeowners Call Ironworks Gate Co. for Ghost Controls Work

We’ve been serving West Hollywood and the surrounding neighborhoods since 1984, and the gates we repaired in our first decade are still on driveways we drive past today. That’s the standard we hold ourselves to.

Our technicians are trained on nine gate-automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Which means if we open your Ghost Controls box and find the problem is actually a wiring issue from an old DoorKing install, or a hinge that was welded by someone who shouldn’t have had a welder, we’re equipped to fix that too. We don’t have to call a second company.

Victor Salinas, who runs the shop, grew up in the Eastside flats of West Hollywood and learned the trade watching his uncle weld ornamental iron on Melrose Avenue. He studied welding and electrical systems at Los Angeles Trade-Technical College, and his daughter still teases him that he talks to motors the same way he talks to people. Steady, and without any drama. That’s how we run every job.

If the gate’s giving you trouble, let’s take a look at it - no guessing, no upselling, just a straight answer.

FAQs