FAAC Keypad & Intercom Repair Nationwide

FAAC Keypad & Intercom Repair: The West Hollywood Owner’s Guide

FAAC keypad and intercom repair in West Hollywood typically runs between $185 and $420 installed, depending on whether we’re replacing the keypad membrane, the intercom handset, or the control board behind it. We carry FAAC-compatible keypads and intercom parts on our trucks, so most West Hollywood jobs are finished the same day we arrive. The way homeowners usually discover the failure is simple: the keypad stops reading a digit or two, the intercom voice turns to static, or the gate simply stops responding to the code that worked fine yesterday morning.

Call (442) 255-3886

What most people do not realize is that FAAC keypads wear out in predictable ways. The buttons lose their conductive coating. The intercom speaker cone dries out in the Southern California sun. And the wire connections inside the housing corrode faster in the marine layer air that hangs over the West Hollywood hills. When Victor Salinas looks at a failed FAAC keypad, he is usually looking at one of those three things. The fix is rarely mysterious. It just has to be matched to the right FAAC series and wired correctly.

Which FAAC Models This Applies To

We service the full range of FAAC entry keypads and intercoms, but in West Hollywood the ones we see most are the FAAC XKP 140, the XKP 130D, the DigiKey, and the older FAAC 455 D keypads paired with swing and slide gate operators. The intercom side is usually a FAAC P105 or a compatible two-wire audio unit mounted at the street. Here is what matters: FAAC made several keypad generations that look almost identical from the outside, but the wiring harness changed between them. A keypad pulled from a FAAC 455 D system will not drop into a newer FAAC E124 control board without a wiring adaptation, and getting that wrong will burn out the new keypad on the first power-up.

OEM FAAC keypads are well made, but the aftermarket equivalents from Security Brands and Linear-compatible units often last just as long for $40 to $80 less. We stock both and we will tell you the honest trade-off. The OEM unit matches the mounting holes exactly. Some aftermarket keypads need a new hole drilled or an adapter plate, which matters when the keypad is set into stucco or a stone pillar at a West Hollywood driveway. We also carry the small things that fail first: the silicone button membranes, the tamper screws, and the weather gaskets that keep moisture out of the housing.

Signs Your FAAC Keypad & Intercom Repair Is Failing

• Some digits work, others don’t. The conductive layer inside the rubber membrane has worn away on the most-used buttons. This is the number one FAAC keypad failure we see in West Hollywood, and the fix is a new membrane or keypad, not a new gate motor.
• The intercom voice is garbled or faint. The speaker cone has dried out or the microphone has corroded. Sun exposure on walls facing south or west does this faster. Sometimes the problem is just a loose spade connector on the back of the speaker, which takes five minutes to fix.
• The gate opens on its own or won’t open at all. Moisture inside the keypad housing shorts the switch contacts intermittently. This is more common in the West Hollywood hills where morning fog condenses on metal housings.
• You enter the code and hear nothing. No beep, no click, no motor sound. That is usually a dead keypad power supply or a broken conductor in the wiring run between the keypad and the control board. Rodents chewing through low-voltage wire behind stucco walls account for a surprising share of these calls.
• The keypad works, but the intercom buzzer does not. The door release relay inside the intercom module has stuck. This is repairable on most FAAC units, but if the relay has arced badly, we will recommend replacing the module rather than rebuilding a part that will fail again.

Replacement Cost & What’s Included

An installed FAAC-compatible keypad replacement in West Hollywood is usually $185 to $340. A full keypad plus intercom replacement together runs $310 to $420. The spread comes down to whether your system is a basic keypad or a keypad with an integrated intercom and door release, and whether the existing wiring can be reused. Our price includes the part, the labor, the wiring check, and programming the new keypad to your existing codes and gate operator. You get the total number before we start, and it does not change unless we find something broken inside the gate operator itself, in which case we stop and tell you before any new cost appears.

Every FAAC keypad and intercom replacement we finish in West Hollywood is covered by our written 90-Day Done Right Promise. If the new part misbehaves or the programming glitches, we return and make it right. No paperwork, no argument. That is the Keystone Standard on every job.

DIY or Call Us?

There are a few safe checks you can do before calling: confirm the breaker for the gate is on, check whether the keypad backlight still lights up, and look for visible water or insect debris inside the keypad housing. If the problem is a dead keypad battery on a wireless FAAC unit, replacing the battery is simple and we will happily tell you which one over the phone. But past that, FAAC keypads involve low-voltage wiring that feeds into the gate operator’s control board, and miswiring a keypad can smoke a $400 control board. This is also not the place for guesswork: the wrong keypad or a shorted wire can leave your gate locked open or locked shut, and a gate that will not close is a security problem on a property, not a convenience problem.

If the gate’s giving you trouble, let’s take a look at it, no guessing, no upselling, just a straight answer. Most FAAC keypad and intercom repairs in West Hollywood are one visit and done. Call (442) 255-3886 and a live person answers, any hour, any day.

FAQs