Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Repair in West Hollywood: What to Know First
FAAC gate repair in West Hollywood typically runs $225 to $485 for most common failures, and most jobs are completed in a single visit. We are an independent FAAC service provider - not affiliated with or authorized by FAAC - which means we fix what’s actually broken instead of steering you toward a new opener. The price is quoted and agreed before any work starts, so the bill never surprises you.
This page is for the homeowner whose FAAC opener has started acting up - the gate that groans, hesitates, or refuses to close - and who wants a straight answer from a technician who has worked on these units for 42 years. Victor Salinas and the Ironworks Gate Co. crew have been fixing FAAC systems across West Hollywood driveways since the days when hydraulic openers still outnumbered belt drives. If your FAAC is doing something it shouldn’t, call (442) 255-3886. A live person answers, day or night.
How FAAC Products Fail - and How We Fix Them
FAAC builds a rugged opener, but every brand has its known weak points. Here is what we see regularly on West Hollywood driveways, and what we do about it.
- FAAC 400 Series hydraulic pumps lose pressure in the summer heat. The 402 and 422 operators are common on older West Hollywood estates, and when June arrives, the hydraulic fluid thins out. The symptom is a gate that struggles to open fully on hot afternoons but behaves in the morning. The fix is a fluid change, bleed, and pressure adjustment - not a new pump. We carry Shell Tellus and the factory-recommended alternatives on the truck.
- FAAC S800H and C720 slide-gate limit switches shift out of calibration. These screw-type limit switches are precise but sensitive. One hard bump from a car or a buildup of debris in the track knocks the stop point off by inches, and the gate starts slamming or reversing. We reset the limits, clean the track, and check the mounting brackets for true - a forty-minute job most of the time.
- FAAC E024U and E124 control boards burn out relays after power flickers. West Hollywood gets its share of transformer blowouts and utility surges. When the power comes back dirty, the relay on the board takes the hit. The gate just sits there, dead, with the keypad still lit. We test the board, replace the relay where possible, and install a surge suppressor so the same failure doesn’t come back on the next brownout.
- FAAC articulated-arm swing openers strip the release mechanism after years of manual use. The 390 and 391 arms have a manual release knob that homeowners twist when the power’s out. After a decade, the plastic threads inside that knob wear smooth, and the arm won’t re-engage. It’s a five-dollar part in most cases, but FAAC doesn’t sell it separately - they sell the whole release assembly. We keep aftermarket replacements in the truck that fit properly and last longer than the original.
- FAAC photocells and safety edges corrode in the coastal air. Even this far inland, the marine layer reaches West Hollywood on enough mornings to matter. FAAC’s standard photocell housings are not sealed against fine moisture, and the terminals oxidize slowly until the gate refuses to close - a classic “reverses for no reason” complaint. We replace the corroded cells, seal the new connections with dielectric grease, and sometimes mount the cells slightly off the ground where they stop collecting splash.
Our FAAC Gate Repair Process
Here is what happens when you call us about a FAAC opener that’s misbehaving.
- 1
The call. A live person answers at (442) 255-3886. We ask what the gate is doing, what model you have if you know it, and how long it’s been going on.
- 2
The visit. A uniformed, background-checked technician arrives on schedule. Before touching anything, we ask you to show us what you’re seeing. Then we run the gate through its cycle and listen. A FAAC hydraulic pump sounds one way when it’s low on fluid and another way when the bypass valve is sticking.
- 3
The diagnosis and the number. We find the fault and quote the repair price before turning a single bolt. You approve it. If the repair is more than you want to spend, the $89 Seasonal Tune-Up option sometimes picks up simple faults, and we’ll tell you if that’s the honest fix.
- 4
The parts decision. For FAAC units, we prefer OEM parts when the failure is safety-related or inside the control board. For wear parts - release knobs, hinges, edge strips, photocell housings - we often use aftermarket equivalents that fit tighter and cost less. We’ll tell you which is which and why.
- 5
The repair and the test. We do the work, then cycle the gate 10 to 15 times. We adjust the force settings so the gate stops cleanly without slamming, and we check the safety edge and photocells with a real obstruction, not just a wave of the hand.
- 6
The guarantee. Every FAAC repair carries the 90-Day Done Right Promise. If it’s not right, we come back and make it right. No paperwork, no arguing.
What FAAC Gate Repair Costs in West Hollywood
No surprises. Here are the numbers for the FAAC repairs we handle most often in West Hollywood.
- Diagnostic visit: $89 service call, waived if you approve the repair on the spot
- Hydraulic fluid change and pressure adjustment (400 series): $180-$260
- Limit switch reset and recalibration (S800H, C720): $140-$220
- Control board relay replacement or board swap (E024U, E124): $220-$485 depending on the board
- Photocell or safety edge replacement: $120-$210 per set, including sealing
- Manual release mechanism replacement (articulated-arm models): $95-$160
- Full FAAC opener replacement (parts and labor): $1,600-$3,400 depending on the operator and gate weight
What moves the price is access - a steep hillside driveway in the Hollywood Hills takes longer than a flat lot on Norton Avenue - and whether the gate needs steel repair alongside the opener work. Every quote is written, itemized, and agreed before we start. Call (442) 255-3886 for an exact number. We also offer $50 off any repair over $250, and senior and veteran customers always get 5% off.
Why West Hollywood Homeowners Call Ironworks Gate Co. for FAAC Work
Because we have been fixing gates here since 1984, and we specialize in exactly this - not fencing, not handyman work, not “and more.” Just driveway and estate gates: the steel, the hinges, the motor, and the keypad. If your FAAC needs attention, our technicians know the unit before the van pulls up.
We also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if you ever switch brands - or if a previous homeowner left you a mixed system - the same crew handles it. Every job, big or small, is backed by the 90-Day Done Right Promise in writing. That is not a marketing line. That is the Keystone Standard we have put on every ticket for over four decades, and it applies to your FAAC repair the same as it did to the first gate we fixed.
Victor grew up in the Eastside flats of West Hollywood, which means he knows these driveways from before most of the current gates were hung. If the gate’s giving you trouble, let’s take a look at it - no guessing, no upselling, just a straight answer.
FAQs: FAAC Gate Repair in West Hollywood
No. As an independent FAAC service provider, we work on units inside and outside of warranty. If your FAAC opener is still under the manufacturer’s warranty, we use OEM parts and follow FAAC’s service specs so the warranty stays intact. We will tell you before we start whether a given repair is better handled through FAAC directly.
Most common FAAC parts - control board relays, release assemblies, photocells, hydraulic fluid, edge strips - are stocked on our trucks. For less common parts, like a full replacement E024U board or a specialty arm, it typically takes two to four business days from our Los Angeles supplier. We will tell you at the quote stage if a part needs ordering, and we do not charge you for the waiting time.
The honest answer: repair until the repair exceeds about 40% of a replacement. A $285 relay repair on a $1,800 system is worth it. A $900 repair on a 15-year-old hydraulic unit with a wearing pump is usually the point to consider a new opener. We will give you both numbers before you decide, and we install new FAAC openers as well as we repair old ones.
In most cases, yes. Emergency calls in West Hollywood are often handled same-day when you call before early afternoon. For less urgent repairs, we typically schedule within one to two days. A live person answers 24 hours a day at (442) 255-3886, so when the gate is stuck open at 9 p.m., you’re talking to us, not a recording.
We handle the whole FAAC system: motor, control board, photocells, safety edge, keypad, hinges, and the steel gate itself. A FAAC opener that passes its motor test but fails a safety edge test is not a completed job. We test every obstruction-sensing device on every repair, and we adjust the force settings so the gate meets current safety standards before we leave.
Then we come back, at no charge, and make it right. That is the 90-Day Done Right Promise, and it is written on every ticket. No receipt-hunting, no arguing with a call center, no “that fault is different.” If the gate is not fixed, we are not finished.
For FAAC gate repair in West Hollywood with an honest quote and the work done right, call Ironworks Gate Co. at (442) 255-3886. Estimates are free, and the price is always agreed before we start.
Written by Victor Salinas, Owner & Gate Repair Specialist, Ironworks Gate Co. at Ironworks Gate Co., serving West Hollywood and nearby areas.