Linear Gate Parts & Welding Nationwide

Linear Gate Parts & Welding in West Hollywood: What to Know First

We repair and weld Linear gate systems across West Hollywood, typically completing most parts and welding jobs in a single visit. Pricing is quoted and agreed before any bolt is turned or bead is laid, so you’ll never open a bill larger than the number we discussed. Most Linear hinge replacements, roller swaps, post repairs, and custom weld work falls between $185 and $650 depending on what’s failed and how much fabrication the job requires.

Call (442) 255-3886

This page is for homeowners in West Hollywood with a Linear gate opener or Linear gate hardware that’s sagging, grinding, sticking, or refusing to close. If your Linear gate is giving you trouble, call (442) 255-3886 and tell us what you’re seeing. We’ll give you a straight answer over the phone, and if it needs eyes on it, we’ll schedule a visit.

How Linear Products Fail - and How We Fix Them

Linear has been on driveways since 1961, and over 42 years of gate work in West Hollywood, we’ve learned where these systems tend to give out. Here are the failures we see most often:

• Hinge weld fatigue on Linear slide gates. The Linear SL and SLR series slide gates ride on steel V-track rollers that bolt to the gate frame. When the gate sags even a quarter inch, the full weight shifts to the hinge-side post, and the original factory welds start to crack. We see this on older West Hollywood driveways where the concrete has settled. The fix is grinding out the cracked weld, re-welding with proper penetration, and often adding a gusset plate so the same failure doesn’t return in two years.
• Broken V-track rollers on the VS-GSL series. The factory rollers on Linear’s residential slide openers wear flat on one side because the gate weight is never perfectly balanced. Once a roller goes flat, the gate jerks instead of glides, and that jerking beats up the motor gear. We replace worn rollers before they take the gearbox with them, which costs a fifth of what a full operator replacement runs.
• Stripped limit-switch cams on the LDO series swing arms. The Linear LDO swing gate operators use plastic limit cams that sit on a threaded shaft. Years of West Hollywood sun and temperature swings make that plastic brittle, and eventually the cam strips and the gate overshoots, slamming the post. We machine replacement cams from aluminum or brass and weld a reinforcing collar onto the shaft. After that, the limits stay put.
• Rusted latch and lock pockets on pedestrian gates. Linear makes a line of pedestrian gate locks that sit inside the gate frame. Water runs down the gate face in our winter rains, puddles in the lock pocket, and corrodes the striker from inside. The gate still closes but won’t latch. We cut out the rusted section, weld in a stainless pocket, and install a new striker with a drain gap at the bottom so water has somewhere to go.
• Frame cracking at the operator mounting plate. On Linear swing gates that have been in service more than a decade, we frequently find hairline cracks radiating from the operator mounting plate. The factory plate spreads force over about twelve square inches, and that’s rarely enough on a heavy estate gate. We weld a larger backing plate behind the original, tying it into the vertical stiles, which stops the crack and gives the operator a stable mount.

Our Linear Gate Parts & Welding Process

Every Linear job we take in West Hollywood follows the same sequence, and we’ll walk you through each step before we start.

1. 1
   We listen first. You tell us what the gate is doing, when it started, and what you’ve already tried. Most of the time, we can narrow the likely cause over the phone and show up with the likely parts on the truck.
2. 2
   We inspect the whole gate, not just the symptom. A sagging hinge is rarely a hinge problem alone. We check roller wear, post plumb, weld integrity, and operator mounting before we touch a tool.
3. 3
   We quote the job before work begins. You get a firm number with parts and labor separated, and we settle the price before a single bolt is turned. No surprises on the bill, ever.
4. 4
   We decide on parts together. For Linear operators, we use OEM parts where it matters for safety and reliability. For steel fabrication like hinge repairs, gusset plates, and post reinforcement, we work with structural steel that matches or exceeds the original. We’ll tell you when aftermarket is equal or better, and when it isn’t.
5. 5
   We do the work, then test it hard. Welds get ground clean and painted. The gate gets cycled repeatedly. We check the close force, the limit points, and the safety edges before we call it done.
6. 6
   You get the 90-Day Done Right Promise in writing. If anything we touched isn’t right, we come back and make it right. No paperwork, no arguing.

What Linear Gate Parts & Welding Costs in West Hollywood

Here are the price ranges we most commonly quote on Linear work in West Hollywood. These are honest ranges, not teaser numbers:

• Hinge replacement or weld repair: $185-$420 depending on gate weight and access
• Roller replacement (pair): $145-$280 installed
• Post replacement (steel post, set in concrete): $450-$950
• Custom welding (crack repair, gusset plate, bracket fabrication): $95-$350 per weld location
• Latch and lock replacement: $120-$260
• Full rail straightening and re-weld: $380-$850

What moves the price is access, gate weight, and whether we’re repairing steel in place or fabricating a replacement section in our shop. The price we quote is the price you pay. Call (442) 255-3886 for an exact number on your Linear gate. Estimates are free.

Why West Hollywood Homeowners Call Ironworks Gate Co. for Linear Work

We’ve been fixing gates in and around West Hollywood since 1984, and we’ve seen every brand the market has thrown at driveways. Linear is one of nine gate-automation brands we service, which matters more than most people think: when a Linear operator shares a driveway with a LiftMaster keypad or a Ghost Controls sensor, we already know how the pieces talk to each other. Most Linear parts and welding jobs are done in a single visit, with the correct fix made the first time.

Victor Salinas grew up in the Eastside flats of West Hollywood, learning to weld ornamental iron from his uncle on Melrose Avenue. He still approaches every Linear gate the same way he did then: find what’s actually wrong, explain it plainly, fix it right. Every job carries our 90-Day Done Right Promise in writing, and a live person answers our phone 24 hours a day, 7 days a week. If the gate’s giving you trouble, let’s take a look at it - no guessing, no upselling, just a straight answer.

FAQs