Linear Gate Installation Nationwide

Linear Gate Installation in West Hollywood: What to Know First

Linear gate installation in West Hollywood typically runs from $850 for a simple pedestrian gate to $4,800 for a full double swing gate with the operator, track, and safety edges. We install, retrofit, and replace Linear operators and complete gate systems in about one to two days on most West Hollywood properties, with the price quoted and agreed before a single bolt gets turned. If you own a Linear opener and the gate itself is failing, or you have a new Linear unit sitting in a box and need it mounted right, this page is for you. Call (442) 255-3886 and a live person answers, any hour.

Call (442) 255-3886

We are an independent Linear service provider. We are not affiliated with Linear or authorized by the manufacturer, but our technicians have installed and repaired Linear equipment across West Hollywood for years, alongside eight other major opener brands. That cross-brand experience matters more than most people expect when a Linear job depends on how the gate was hung in the first place.

How Linear Products Fail - and How We Fix Them

Linear builds solid operators. The failures we see on West Hollywood gates are rarely the motor itself. More often, it is the marriage between the opener and the gate that was never quite right, or a limit switch that gave up in the heat. Here are the five patterns we see most on Linear installs and callbacks.

• Linear LDO series limit switch drift on hillside driveways. The LDO50 and LDO33 are workhorses, but their mechanical limit cams ride on plastic gears that wear faster on sloped West Hollywood properties, where the gate works harder against gravity. The symptom is a gate that stops three inches short of open, or creeps past the close. We replace the limit assembly with the updated metal-gear part and re-set the travel so the gate lands exactly where it should, every cycle.
• Linear ACT31 and ACT34 arm brackets pulling loose from stucco columns. West Hollywood has a lot of 1950s and 1960s stucco-over-wood-framed columns. The wood behind the stucco dries and splits, and the arm bracket starts to sag. The opener then fights itself, the gate jerks, and the homeowner assumes the operator is bad. We remove the arm, inspect the column structure, install a steel backing plate across the load path, and re-mount the bracket so the arm is pulling against steel, not dry wood.
• Linear APeX and LRA control boards killed by Southern California brownouts. The APeX series runs on a motherboard that is sensitive to the voltage wobble common in the hills above Sunset Boulevard during summer heat. A board that has been nudged by brownouts will drop programmed limits or forget the wireless keypad. We replace the board with a factory Linear part and install a surge suppressor on the power run so it does not happen again.
• Mismatched photo eyes from a previous low-bid install. Linear’s safety system is designed around its own photo eyes, and the wiring polarity matters. When a prior company installed generic eyes to save money, the gate will randomly reverse or refuse to close. We pull the aftermarket eyes, run fresh shielded wire, and install the correct Linear photo eyes so the safety circuit talks to the board the way it was designed to.
• Linear MegaCode receiver interference in dense neighborhoods. Tighter West Hollywood lots mean multiple gates within a few hundred feet, and older Linear receivers on 318 MHz can pick up a neighbor’s remote. The owner swears the gate opens by itself. We re-code the receiver, disable the unused channels, and when needed, switch to a newer Linear receiver with rolling-code isolation so your remote is the only one the gate listens to.

Our Linear Gate Installation Process

Every Linear job we take in West Hollywood follows the same sequence. It keeps the work predictable, and it keeps the bill predictable too.

1. 1
   Call and describe what the gate is doing. A live person answers, day or night. We ask a few questions about the gate type, the opener model if you know it, and when the trouble started.
2. 2
   On-site inspection. Our technician arrives in a uniformed truck, walks the gate through a full cycle, checks the operator, arms, hinges, track, and safety system, and listens to what it sounds like. Victor Salinas has said for years that a gate tells you what is wrong if you stand still long enough to hear it.
3. 3
   Straight diagnosis and a written price. We explain what failed, why it failed, and what it will cost to make it right. We settle that price before work begins. If a factory Linear part is the right call for your warranty or reliability, we use it. If a quality aftermarket part does the same job for a fairer price and does not compromise the system, we will say so and let you choose.
4. 4
   The work. Most Linear installations and repairs are completed in a single visit. Installation, welding if needed, electrical, programming, safety edges, keypads, and remotes. We work the way we would in a family home, because we are in one.
5. 5
   Cycle testing and safety verification. We run the gate through 30 full open-and-close cycles, test the reversing force, photo eyes, and any keypad or entry system, and adjust travel so the gate lands square and locks correctly.
6. 6
   Cleanup and a written 90-Day Done Right Promise. We walk the job with you, hand you the guarantee, and leave the driveway cleaner than we found it. If anything is not right within 90 days, we come back and make it right. No paperwork, no argument.

What Linear Gate Installation Costs in West Hollywood

Straight numbers, because guessing does nobody any good. Here is what Linear work generally runs in West Hollywood:

• Linear operator installation only (customer has a gate): $850 to $1,600 depending on swing versus slide and the power run required.
• Linear swing gate with operator, arms, safety edges, and two remotes: $2,400 to $3,800 for a single driveway gate.
• Linear double swing gate, full system: $3,200 to $4,800 with steel frame, operator, hinges, safety edges, and programming.
• Linear pedestrian gate with keypad and strike: $1,400 to $2,600 for a welded steel gate sized to your opening.
• Retrofit a Linear operator onto an existing gate: $950 to $2,100 including new brackets, arms, and full safety setup.

The two things that move the price most are the gate’s weight and the condition of the column or post the operator mounts to. Older West Hollywood steel gates are often heavier than owners realize, and a 40-year-old wooden post that looks fine from the street may have rot behind the stucco. We check all of that before we quote, and the price we give is the price you pay. Estimates are free. Call (442) 255-3886.

Why West Hollywood Homeowners Call Ironworks Gate Co. for Linear Work

We have been serving West Hollywood and the surrounding streets since 1984, and we plan to be here for another forty years. That matters when you are choosing who works on a gate you will walk through every day. Every job we complete is covered by our 90-Day Done Right Promise, written and handed to you before we leave. We do not make you fill out forms to get us back.

Our technicians are background-checked and uniformed, and they work on nine opener brands. That breadth is the real advantage on a Linear job: when a Linear opener mounts to a gate that was originally built for a LiftMaster or a Mighty Mule or a Ghost Controls operator, we have seen that combination before and know what the retrofit involves. If your Linear unit is beyond saving, we can talk through what a DoorKing or LiftMaster replacement would cost, honestly and without pushing. One phone call, one straight answer.

FAQs